Changelog STEREOPING Synth Programmer firmware for Waldorf Microwave

16.09.2021 - Update to V1.68:
	* bugfix: Submenu GLIDE 4/4 program naming - display could crash when receiving much midi data like e.g. ModWheel

24.08.2021 - Update to V1.67:
	* minor bugfixes in CHORD MEMO
	* bugfix: CC-numbers were displayed (leftover from debugging) while receiving remoting CC data

20.08.2021 - Update to V1.66:
	* bugfix: CHORD SETUP: display crash when changing chord slots quickly
	* added feature to initialize all CHORD slots: hold MOD button while the Stereoping logo shows up until message "Please sync 2 MW" appears 

10.06.2021 - Update to V1.65:
	* bugfix: PREFS were not saved


26.05.2021 - Update to V1.63:
	* bugfix: after pressing CUR in PATCH mode, the Programmer jumps directly back into PLAY mode as described in the manual

03.05.2021 - Update to V1.62:
	* added feature: PREFS setting 'Limit Waves' to prevent running the STARTWAVE knobs into tri/sqr/saw
	* added feature: User Wavetable editing and parametrized randomizing
	* added feature: User Waves drawing and parametrized randomizing

02.04.2021 - Update to V1.58:
	* bugfix: sporadic screen crashes when changing Chord Memo slots
	* bugfix: Chord Memo triggernote displayed one octave to high
	* added feature: Editing of User Wavtables and randomizer for User Waves

09.10.2020 - Update to V1.55:
	* bugfix: awake from Screensaver by heavy Midi traffic caused hangups 

15.07.2020 - Update to V1.53:
	* bugfix: after moving knobs in RANDOMIZER the 1st display line was not updated correctly

12.05.2020 - Update to V1.52:
	* added Feature: Encoder No 4 now changee the Wavetable - unless user is editing the wave envelope

14.01.2020 - Update to V1.51:
	* bugfix: LEDs stayed dark after Program request
	* bugifx: CC-Translator did also translate on channels being different to Programmer's basechannel
	* bugfix: CC-Translator sent ParaChange commands to last selected Instrument of Programmer's MultiMode
	* bugfix: CC #80 was blocked although not being used by CC-Translator. Gets through now.

14.01.2020 - Update to V1.50:
	* bugfix: CC-sending was blocked after ProgramChange on MIDI IN 2
	* bugfix: "Wave2 M2 Modifier" appeared as "Wave1" in display
	* bugfix: Program name - letters did not reach first (Space) and last ("z") letter.
	* bugfix: after editing name and moving GLIDE RATE the display jumped back to naming display, changing letters on incoming midi notes
	* added Feature: CC Mode
	* added Feature: entering PREFS "reboots" Display to fix garbage characters appearing in very rare occasions
	* added Feature: entering PREFS sends ALL NOTES OFF to Microwave to stop hanging notes

21.04.2019 - Update to V1.09 - Bugfix (Compare was not possible after request with CUR. WAVE STARTSAMPLE showing "fre" (free) for the value of 0

08.04.2019 - Update to V1.07 - bugfix (OSC1+2 MOd Quantisize as well as OSC2/WAVE2 link mode did not change) and new poweruser-feature: use pots to adjust mod intensities of mods slots directly while holding MOD in PLAY mode (please mind updated manual in version 1.07). Patch mode allows request of current Program with CUR command.

21.03.2019 - Update to V1.05 - the display's special characters were missing. On VS the arrows of the NV LOOP Screen, on the Microwave the multi instrument in the upper right corner

16.04.2018 - Update to V1.02 - Bugfix: Program parameters changed on selection of some pots in Modulation mode
15.04.2018 - Update to V1.01 - Bugfix: GLIDE-Temperment stopped with TT4